You may need to press the dial in to be able to turn it. Turn the dial from the ‘off’ position to the ‘pilot’ position.
Most of them are made of glass, so be careful how you put them down.
How to light a gas fireplace. You should see a black or red button. Our own gas fireplace insert is an older model and the pilot light is the standing flame type rather than the intermittent pilot ignition found often found. The pilot will light the gas and then the entire fireplace will be operational.
These should be toward the bottom. Push in the gas valve start button while lighting the pilot with a match or lighting device. Remove the outer cover, so you can ignite the pilot light.
The steps involved in lighting your pilot on your gas fireplace include: Depending on how long it’s been since the gas fireplace was last used, ignition may take several attempts before igniting. Lighting a gas fireplace using a key.
The procedure commonly followed for lighting a gas fireplace with a dial and separate spark ignitor button can be: Press this button and you should see the pilot light turn on whenever you turn the gas control to start the gas. How to light a gas fireplace.
A benefit of ipi mode is that it is more cost effective, efficient and environmentally friendly. Push in the pilot knob, which manually sends gas into the system. The first think you want to do is pull the cover off the fireplace.
Follow these steps to light and turn on a gas fireplace. Wear safety gloves if you are new to operating a fireplace. Continuously press the ignition button to generate the sparks until the pilot lights.
Most fireplaces, unless specified otherwise in the manual, have a gas control knob which is next to a colored button. Hold the valve in the light position for 30 seconds until you see a flame. Set the control to the on position.
The great thing about a gas fireplace is that it is easy to light and works quickly to heat up your home. If the gas valve knob is far away from the burner, ask someone else to turn the key or operate the lighter. This video will show you how to light a gas fireplace with a piezo spark ignitor.
Turn the knob from the “off” to the “pilot” position. Push the igniter button once every second until it lights. Hold the gas valve at the light setting for 30 seconds or until you see a flame.
Locate the gas control dial. Press the button to verify that there’s a spark at the end of the pilot tube. Adjust the shutoff valve of your fireplace to the right position:
For specific instructions, refer to your fireplace’s operating manual. Turn the control to the on position; The dial may need to be depressed to allow gas to the.
In most cases, you’ll have to light your fireplace pilot light just once a year. Set the pilot position to “light,” or center. Push in the pilot knob, which will then manually send gas into the system.
If you release the knob and the clicking stops, you will need to hold the ignition knob in until you see flames begin to catch along the gas line under the logs or tempered glass beads. Easy steps to light gas fireplace. Ignite it and get away quickly from the fire pit.
How to light a gas fireplace with an electronic ignition starting system. Some gas fireplaces are lit by a wall switch, while others require a control panel or a fireplace key. Go back to the knob for the pilot light ignition.
Turn the knob to the on position. This is the system working to spark the gas to light the pilot. A gas fireplace pilot light, which can also be referred to as just the pilot in a gas fireplace, is an important part of gas fireplace design and essential for helping gas fireplace flames to start quickly and efficiently.
If the fireplace hasn't lit up within 10 seconds, wait at least 10 seconds before trying again. Remember to do this when you are ready to ignite the pilot light of your gas fireplace. Consult the owners manual if you have one.
Reset the knob to the pilot position : Keep pushing the button until the pilot light turns on. Read and follow the instructions that came with you.
Pull fixed glass assembly off of fireplace. Press and hold down the gas control knob, then press the igniter button multiple times, as needed, until the pilot flame ignites. First, turn your gas fireplace’s knob from the “off” to the “pilot” position.
If there’s a battery backup, the pilot light could be on without any gas going to the fireplace. If there is a glass door, open it. Here’s how to light a gas fireplace with a control panel.
When you do so, gas starts to flow through the main burner assembly. Once the pilot lights, keep holding down the gas control knob for 20 to 30 seconds to allow time for heating up the thermocouple (a safety device), then release the knob so it pops back up. Ensure that the valve is properly aligned with the gas line of your fireplace for ultimate control of the flow of the fuel.
Bring the lighter near the fireplace and move the gas valve key in a counterclockwise direction. This is a critical safety precaution that gives the buildup of gas if the pilot light is hard to relight. Light a match or butane candle lighter and hold it near the burner in the fireplace.
Push the start button while lighting the pilot with an igniter.